Summary
Shelf Setup and Center Pole Assembly
Measure shelves according to your system configuration. Use the center pole with a wheeled base, attaching shelves at specific heights: bottom shelf at 8 inches, second shelf at 22 inches, and top extension arm shelf at the very top.
Component Positioning
Install the CO2 tank holder down the back center column, position the gastroscope pole holder at the second shelf level, and secure the surge protector between the two posts using zip ties.
Triangular Base and Monitor Mount Assembly
Place the triangular base on top of the center pole and secure with bolts. Install the monitor mount with proper orientation (warding and monitor facing up), then position the monitor over the center pole and tighten.
Monitor and Cable Setup
Mount monitor bracket over remaining screws ensuring proper orientation. Connect DVI cable from monitor to gastroscope inputs. Install gastroscope hook at monitor height. Connect gastroscope processor power brick to the surge protector.
Final Verification
Turn on the monitor power. Access the menu and change input to DVI. Verify image display on screen once all camera and gastroscope connections are confirmed.
Transcript
Check page two of your instructions whether you’re setting your system up as a laparoscopic system you’ll want to measure your shelves from the base to the first shelf, then the second shelf and then the third shelf. If setting up for a laparoscopic system and gastroscope system you’ll want to measure your shelves at different heights and use your center pole, turn it upside down and then you’ll use your base with the wheels. You’re looking for each of the holes that have a C and a C next to it. You’ll use your biggest Allen wrench, you’ll use your biggest screws along with a washer and then you’ll line up the holes.
With your screws almost all the way out and loose Jimmy them down the center pole to get your shelf into place. If setting up the gastroscope system or just the laparoscopic system place your bottom shelf at about eight inches from the base to the first shelf.
It’s doing just the laparoscopic or the gastroscope system place your second shelf 22 inches from the base. Take your top extension arm and place it almost at the very top of the center column. This is your CO2 tank holder. You’ll place this down the back center column and just drop it all the way.
You’ll take your gastroscope pole holder and locate it down to about the level of your second shelf. And then the other one you’ll do the exact same thing with take your zip ties and to make them long enough just put it in gently like that and then you’re going to use these to hold down your surge protector. You’ve placed your surge protector in between the two posts. You’ve used your zip tie to be able to grab it and then that can strap around the top of your post.
Take the triangular base and place it on the top of the center pole. You’ll take your remaining four bolts, screw them into the top with your largest allen wrench. Center pole goes into the triangle and screws down. Small set screw on your small Allen wrench will go right into there to hold the black post sturdy.
You’ll take your cord holder and put it down the black center pole. You’ll take this ring and put your set screw into it with your smallest allen wrench and then click that at about your neckline.
Take your center pole and slide it down into the two braces with the pole being up above your head. You’ll take this and screw it into your monitor mount just loose. And that will stay out the two screws in the bottom of this plate and then the four center screws.
Take your monitor mount and it will go over the other screws that are still remaining. Make sure your wording is facing up with this and your monitor is also facing up. I’ve used my back bracket to hold and control my screw. Place your monitor over the center pole down to your ring.
And then just tighten it up just a little bit. This is your gastroscope hook. When you put this together you’ll put the screws in there. And then the back side will have the screws to be able to tighten it down. And the hook will slide down your pole to about the height or a little higher than your monitor.Â
Here’s your cable guide for the first part of your power supply for your monitor and loop this under here pull this up and then you’ll see a little notch right in here that goes to the power supply.
Use your DVI cable, the black one that came with the gastroscope and plug that into the DVI input there and just screw it tight. Back plate can go in and then the two remaining screws can go in there and there.
Use the brick that came with the gastroscope processor that will plug in the back of the gastroscope. And then the other end will plug into your surge protector. EVI cable will plug into the not the yellow side, the opposite side and screw down nice and tight.
Make sure your gastroscope hook is holding your gastroscope so that it’s positioned off the floor and without too much tension on your gastroscope processor. You’ll turn your power on on your monitor. You won’t get any image so you’ll want to hit the menu button, the input.
And then change this to DVI with the up arrow and then hit ok. And then if your camera signal cable is connected and your gastroscope are connected you’re going to have an image on the screen.